Table of Content
Crimping is a common method that allows you to connect loads of wires in a short amount of time. You won’t be using heat guns or soldering guns, nor will you have to twist wires and nuts repeatedly. If you want to give shrink tubing a try, get a heat gun and follow the steps under the next subheading. Soldering your speaker wires is a surefire way to get the best connection, but it’s the most complex method. You’ll need a soldering gun and the right tools to get the job done. There are plenty of kits that come with everything you need.
They’re the most basic level of cable, and you won’t even need to go near them if you’re only dealing in HD devices. Do everything possible to ensure wires are the same length, because then if you do get any resistance, at least it’ll be the same. This is obviously another important factor when choosing the right cables, and will be dependent on the kind of setup you’re looking to build.
Heavy Duty 12 Foot High Quality Speaker Extension Cable for Samsung Systems
If everything is connected as it should be, your speakers are additive, which is good. These are another basic audio cable, and are typically used for sending high quality audio over short distances. They’re used for sending a signal from your antenna, satellite, or cable TV box to your TV. A coaxial cable sends both audio and video signals, but does so separately within the same cable. HDMI cables are generally inexpensive, but costlier models will usually offer better audio and video quality. Realistically, these are probably one of the few cables you won’t need, but it’s useful to know what they are and which devices need them.
Most importantly, you don’t want to cut corners when it comes to cables. So, to help you work out exactly what you need, I will be presenting a list of the 9 cables you need for a home theater. A loudspeaker, or simply speaker, is an electromechanical transducer which converts an electrical signal into sound. Getting the proper tools will allow you to have the best chances of success. Fortunately, this task is fairly simple and straight-forward. You won’t have to worry about making mistakes if you get everything together before you start working.
Speaker Cables
To make this list easier, I’ve divided the types into audio and video, seeing as these are the two types you’ll need. First up are video cables, as it’s a longer and slightly more complicated list. The longer a wire, and its respective connections, are, the more resistance you’ll have in your setup.
Unlike composite video cables, a HDMI lead carries video and audio signals through the same input connection, meaning all you need to do is plug in and go. They can provide HD video and up to 32 channels of audio. It comes with enough heat to use on shrink tubing, and you’ll also receive plenty of tubes that you might be able to use. Using wire cutters, remove about one inch of the rubber coating on the wire. It should be about as long as the depth of the butt splice since it’ll have to slide all the way to the back.
extension cords
More resistance means quieter and less clear sounds, so it’s important to keep a check on this. Using the crimping tool, firmly squeeze the butt splice over the wire. You should be able to tug the wire without it wiggling or coming out of the connection. Move down the splice and squeeze the crimping tool until you reach the end. Repeat this process for both wires connected to the butt splice. If you squeeze the trigger for too long, it’ll burn the wires and ruin the connection.
Generally, you want to try and keep wires as short as possible. This will mean less resistance in your setup, and so you’ll get the most out of your speakers. After all, conductivity ensures you’re getting exactly the quality you expect from your devices. I was a little wary that this would not be what I was looking for so I started by ordering one cable.
Grab the new gauge wire that you purchased from the hardware store and create a small twist at the end. The only downside of using wire nuts is that improper installation tactics can lead to loose ends. If they get too loose, it could cause disconnections or electrical arcing, a symptom that causes sparks and fires. The good news is that you’re about to learn how to avoid both of those issues. If your speakers are attached to the home entertainment system, you’ll need a screwdriver. Unscrew the connections to free the wire, then place the speaker aside.
You can use the crimping tool or the wire cutters if they have gauge slots. All you have to do is locate the number on the tool, slide the wire through, squeeze, and pull the rubber. Next, you’ll need to disconnect the speakers from the entertainment system. This might seem obvious, but you’d be surprised to know the number of people who forget it.
For standard audio and visual cables, you want to start considering alternatives over distances of 10ft, although this will vary depending on the cable. If it doesn’t have an impact on the device’s performance, it can impact conductivity and the lifespan of cables. Ensure your devices have plenty of space around them, and whatever you do, don’t pile them all into a cupboard with the door shut. This isn’t necessarily connected to wiring, but it’s always worth mentioning. Many devices in a home theater system produce a lot of heat, which is never a good thing for electronics. This might seem incredibly basic, but it’s surprising how easy this is to get wrong.
If you’ve never used a soldering gun, then you might want to try a different method. It can be unsafe if you’re not familiar with the process. Sound Certified mentions that you’ll have to get the right size wire gauge. That’s the only way that you’ll be able to extend your wires, and it’s necessary for every method. You can choose various lengths, some of which come with a rubber coating and others that don’t. WikiHow mentions that turning off the power is the first step that you should follow.
Much like you would’ve done in the crimping method, expose about one inch of the wire. Slide the wires into both ends of the crimping tube, ensuring that the wires touch and overlap one another. Some people prefer to twist the wires inside of the tube for extra security. Buying cables is probably the most boring part of setting up a home theater, but it’s possibly one of the most important. Again, resistance increases with length, so if you’re using a lot of wire, make sure the resistance is low.
You’ll need a package of these to match the correct gauge of wire for the project. The good news is that you can spend a little bit more to get them as a part of your wire cutters and other tools. Disconnecting the speakers allows you to keep everything neat and organized. You won’t have to worry about going back and forth, trying to figure out which wire goes to which speaker. Instead, you’ll have everything labeled and ready to go when you get back from the hardware store.
No comments:
Post a Comment